CABINET FILLER STRIP SCREWS
GRK NARROW HEAD TRIM SCREWS
GRK FILLER STRIP SCREWS
IN THIS GUIDE:
› CABINET CLAW: PONY CLAMP FOR CABINETS
› CABINET JACK: FASTCAP UPPERHAND
› SCRIBING TOOL: TREND U/E WALL SCRIBE
› GAP FILLER: COLOR PUTTY
While professionals have the right tools and know-how, DIY cabinet installers may need to learn how to install a filler strip properly. But after installing countless kitchens, there are a few tricks I’ve learned on how to install cabinet filler strips the right way.
Installing filler strips comes down to a few key steps:
- If needed, cut the filler strip to the proper width
- Attaching the strip to the cabinet using clamps and then screws
- Temporarily placing the cabinet to check for fit
- Scribing the filler strip to let it match other cabinets or the wall
- Hiding any gaps with (my favorite) color putty
While this is a seemingly simple step in a cabinet installation project, it can be the most difficult. In this guide, learn the tricks and tools you’ll need to do a proper job.
Page Contents
How to Install Cabinet Filler Strips
1. Layout the Cabinets First
Before installing any filler strip, make sure to layout all cabinets, both uppers and lowers, to ensure both upper and lower cabinet spacing is considered.
Since the upper cabinets are typically installed first, the filler strips on the upper cabinets MUST be appropriately laid out to match the lower cabinets.
An example of this layout preparation is aligning the microwave cabinet gap directly over the range below. If you space the upper cabinets and don’t match the lower cabinets, your content and microwave will be out of alignment.
Once you have the layout, write down the rough widths of the strips you’ll need for later reference.
2. Cut the Filler Strip to Width and Length
Next is ensuring the filler strip is the correct length and width.
Fortunately, in most factory cabinets, the measurements match your cabinets.
But that leaves the trickier job of adjusting the width to you. Need help cutting the strip? Here are a few options:
- Use a table saw if you have access to one
- A circular saw with a rip-cut track guide is a great (inexpensive option)
- For less than a 1/4″ in width adjustment, a belt sander is slower (using a 40-60 grit belt). Use a wood scribe to mark a line.
3. Connect the Filler to the Cabinet
After making sure the strip is the right size and cut to dimension, you’ll need to install it to the edge of the cabinet.
There are a few options for this step, but I recommend the following:
- Using a cabinet claw to connect the face frame to the cabinet
- Or, use a wood cabinet clamp to hold a cabinet filler to a frameless cabinet.
After the filler strip is clamped to the cabinet, use the guide bushing and a LONG 1/8″ drill bit to drill a pilot hole into the filler. For my projects, I like to use a GRK trim head screw, which you can learn more about in our guide to cabinet screws.
4. Install the Cabinet
Once the filler strip is attached to the first cabinet, install the cabinet and repeat these steps as needed.
5. Hide Gaps With Color Putty
Lastly, cabinet installation is all about tricks of the trade.
And one of my secret weapons is using Color Putty to hide gaps between cabinets or nail holes in the crown molding or toe kick.
How to install cabinet filler strips against the wall
Because filler strips can cause visual imbalance, installing them against the wall is a great way to offset their visual impact. And by doing this, you avoid a cabinet-to-cabinet mismatch, such as an extra gap between one set of doors vs. another.
When installing cabinets against the wall, a scribing tool will guide your pencil and leave a perfect contour on the filler strip for sanding.
Steps:
- Cut the filler strip to length with a miter saw.
- Rip the filler strip to width with a table saw and fine tooth blade.
- Clamp the filler strip to the cabinet using a cabinet claw.
- Drill a pilot hole through the cabinet frame and partway into the filler strip. Tip: use a drill bit the size of the screw shaft (minus threads).
- Use a face frame screw to connect the strip to the cabinet.
- For upper cabinets, set the cabinet on a cabinet jack.
- Using a sharp pencil with a scribe, level the cabinet and then run a pencil against the wall and down the entire length of the cabinet filler.
- Use a belt sander to remove material on the wall side of the filler strip
- Fit the cabinet and make minor adjustments to the filler strip for a perfect fit.
- Hide any small gaps with (my favorite) Color Putty by working it into any holes with your fingers and wiping away the excess.
How to Install Filler Strips on Upper Cabinets
Installing filler strips on upper cabinets takes one of two forms:
- Fitting strips between cabinets
- Or installing a strip between the wall and cabinet
While installing filler strips on upper cabinets is similar to installing against the wall, you’ll want to use a cabinet jack and scribe.
Tips:
- Start from corner cabinets and work your way out
- Try to hide filler strips in the corner
- Make sure to line up the upper layout to the base (e.g., oven alignment)
- Lastly, don’t be afraid to split the filler strips in two and use multiples to reduce the visual impact
Installing filler strips between cabinets
Installing filler strips between cabinets is done the same as against the wall.
However, you’ll have the luxury of installing the filler strip to the cabinet first and then choosing to sand (or plane) the next cabinet to match.
Steps:
- Cut the filler strip to length with a miter saw.
- Rip the filler strip to width with a table saw and fine tooth blade.
- Optional but preferred to remove saw tooth marks: run a portable planer down the filler strip for a perfect edge.
- Clamp the filler strip to the cabinet using a claw or clamp.
- Drill a pilot hole through the cabinet frame and partway into the filler strip. Tip: use a drill bit the size of the screw shaft (minus threads).
- Connect the strip to the cabinet using a GRK face frame screw.
- For upper cabinets, set the cabinet on a cabinet jack.
- Fit the cabinet and make minor adjustments to the filler strip for a perfect fit.
- Hide any small gaps with (my favorite) Color Putty.
Planning your cabinet filler strip widths
While most cabinet professionals prefer to use something other than cabinet filler, they sometimes can’t be avoided. The #1 issue with filler strips is they can create a visual imbalance between cabinets.
- Use corners and walls to hide filler strips
- Avoid putting large filler strips in the middle of cabinet runs
- Rip filler strips in two and use multiples to balance their visual impact
- Make sure upper and lower cabinets are planned together
- Finally, before installing the first filler, lay out all strips and check plans and room dimensions to ensure everything will fit.
Finishing cabinet filler strips (optional)
I like to finish the cabinet strips before installing them. By doing this, you will make sure the ribbon matches the neighboring cabinet. Also, having the filler strip “free” to work on will let you easily stain, paint, or apply urethane or other sealants. Finally, you also get to ensure it matches the cabinets before you install it, especially if it doesn’t come with the cabinets.
Tip: Looking for a wipe-on wood sealer that drys in an hour and is simple to apply? I have used General Finishes Arm-R-Seal for almost twenty years, and it always produces a quick and high-quality finish. Dry time in under an hour is a huge time saver.
Finding cabinet filler strip material (optional)
Don’t you have a piece of wood that came with the kitchen? Don’t worry; a few options exist to get what you need.
To find cabinet filler strips, you have a few options:
- Call the manufacturer to order pre-made, finished strips matching your kitchen wood and color.
- If you are painting the cabinets later, head to a local Home Depot or Lowe’s and grab a filler strip from their kitchen area. If it’s finished, install it backward if needed.
- For natural or stained cabinets and the manufacturer isn’t an option, find a hardwood supplier such as Rockler (a favorite of mine who has every hardwood imaginable) or check on Amazon. Sherwin Williams or another paint store can help with a match.
- If ordering cabinets, plan to over-buy these filler strips upfront. A few dollars now will save you a headache later on.
Frequently Asked Questions on Installing Filler Strips
How do you scribe a filler strip?
First, cut the filler strip to the required width and attach to the cabinet. Next place it against the wall and use a sharp pencil or scribing tool traced against the wall to transpose the wall curve to the filler strip. Lastly, remove the cabinet and use a belt sander to sand away the excess. I prefer to run the belt sander at a negative angle to the face of the frame to give it a slight “point”. Repeat the sanding step as needed.
What is a cabinet filler strip?
A cabinet filler strip is a piece of wood inserted between two cabinets to allow factory-sized cabinets to fit a wall of any length. A filler strip can be placed between two cabinets or against the wall to “fill” the empty space between cabinets.
How do you fill the gap between two cabinets and the wall?
A filler strip is used to fill the gap between two cabinets and the wall. Due to factory cabinets coming in standard widths, such as 24 and 36-inches, they will not fit walls with varying odd/fractional dimensions. Filler strips are almost standard in most kitchen cabinet installations that do not use custom-built cabinetry.
How do you hide gaps between the filler strip and the wall?
First, a proper installation shouldn’t have a gap. However, if a gap is present it can be filled with white paintable caulk and painted over. And gaps in filler strips between cabinets can be filled with a rub-in and wipe off putty (that doesn’t require sanding).
Summary
Hopefully, this article helped your cabinet filler strip installation. Remember to subscribe and check the following articles for other tips and tools.
Recommended Reading
Cabinet Installation Series
Planning & Tools To Install Cabinets
Guides for Cabinet Installation
Finishing Cabinets With Molding and Hardware
- 𝐄𝐟𝐟𝐢𝐜𝐢𝐞𝐧𝐜𝐲 - Manram Cabinet Clamps are...
- 𝐏𝐫𝐚𝐜𝐭𝐢𝐜𝐚𝐥𝐢𝐭𝐲 - Manram Cabinet Clamps...
- 𝐃𝐫𝐢𝐥𝐥 𝐆𝐮𝐢𝐝𝐞 - Equipped with a pilot-hole...
- 𝐂𝐚𝐬𝐞 & 𝐅𝐞𝐥𝐭 𝐏𝐚𝐝𝐬 - The accompanying...
- 𝐒𝐩𝐞𝐜𝐢𝐟𝐢𝐜𝐚𝐭𝐢𝐨𝐧𝐬 - The clamps are...
- ⭐【Unique Advantages】- In order to avoid drilling directly with an...
- ⭐【Metric + Imperial Scale】- Contains metric + imperial double sizes....
- ⭐【Detachable & Portable】- Cabinet hardware installation template...
- ⭐【Time Saver Quick Drilling】- Cabinet hardware template tool a full...
- ⭐【Jig Widely Application】- Cabinet hardware jig is ideal for...
- 【PONY 8510 Cabinet Claw】Complete your cabinetry projects in a fraction...
- 【Dimensions】 Works on stiles from 1-1/2 inch to 2 inch; Throat Depth:...
- 【Pilot-Hole Drill】 There is a pilot-hole drilling guide on one end. The...
- 【Protection Pads】 Comes with 4 sets of protective rubber pads to...
- 【Professional】Professional, quality installation is achieved at a...
- Home Improvement Essentials: WORKPRO 3rd hand support pole, which has...
- Rotating Head with Non-slip Pads: Iron-made pads and an additional pair of...
- Heavy Duty&Premium Quality: The stem rod is made of high-density metal and...
- Hands Free&Labor Saving: This extension pole secures building materials to...
- Wide Applications: Offering a third hand to help lift, brace, and support....
- The Cabinet Claw Is An Unique Tool Which Combines The Multiple Steps Of...
- Clamp Specifications: Works On Stiles From 1-1/2 Inch To 2 Inch; Jaw Width:...
- Easy Use To Install And Highly Durable. Protective Pads Protect Cabinets...
- Face Frame Stiles Can Be Tightened, Aligned, Pre-Drilled And Fastened While...
- A unique tool which combines the multiple steps of face frame cabinet...
Last update on 2024-11-24 at 18:49 / Images from Amazon
- About the Author
- Latest Posts
Eric has been a professional woodworker for over thirty years and has worked in small cabinet shops making everything from kitchen cabinets to hand-made furniture. Now working from a home woodworking shop Eric is sharing his passion for woodworking, tool advice and how-to knowledge from his Minnesota-based woodshop.
